156 lines
3.8 KiB
C
Executable File
156 lines
3.8 KiB
C
Executable File
/*
|
|
* D-Link DIR-685 router I2C-based Touchkeys input driver
|
|
* Copyright (C) 2017 Linus Walleij <linus.walleij@linaro.org>
|
|
*
|
|
* This is a one-off touchkey controller based on the Cypress Semiconductor
|
|
* CY8C214 MCU with some firmware in its internal 8KB flash. The circuit
|
|
* board inside the router is named E119921
|
|
*/
|
|
|
|
#include <linux/module.h>
|
|
#include <linux/i2c.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/input.h>
|
|
#include <linux/slab.h>
|
|
#include <linux/bitops.h>
|
|
|
|
struct dir685_touchkeys {
|
|
struct device *dev;
|
|
struct i2c_client *client;
|
|
struct input_dev *input;
|
|
unsigned long cur_key;
|
|
u16 codes[7];
|
|
};
|
|
|
|
static irqreturn_t dir685_tk_irq_thread(int irq, void *data)
|
|
{
|
|
struct dir685_touchkeys *tk = data;
|
|
const int num_bits = min_t(int, ARRAY_SIZE(tk->codes), 16);
|
|
unsigned long changed;
|
|
u8 buf[6];
|
|
unsigned long key;
|
|
int i;
|
|
int err;
|
|
|
|
memset(buf, 0, sizeof(buf));
|
|
err = i2c_master_recv(tk->client, buf, sizeof(buf));
|
|
if (err != sizeof(buf)) {
|
|
dev_err(tk->dev, "short read %d\n", err);
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
dev_dbg(tk->dev, "IN: %*ph\n", (int)sizeof(buf), buf);
|
|
key = be16_to_cpup((__be16 *) &buf[4]);
|
|
|
|
/* Figure out if any bits went high or low since last message */
|
|
changed = tk->cur_key ^ key;
|
|
for_each_set_bit(i, &changed, num_bits) {
|
|
dev_dbg(tk->dev, "key %d is %s\n", i,
|
|
test_bit(i, &key) ? "down" : "up");
|
|
input_report_key(tk->input, tk->codes[i], test_bit(i, &key));
|
|
}
|
|
|
|
/* Store currently down keys */
|
|
tk->cur_key = key;
|
|
input_sync(tk->input);
|
|
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
static int dir685_tk_probe(struct i2c_client *client,
|
|
const struct i2c_device_id *id)
|
|
{
|
|
struct dir685_touchkeys *tk;
|
|
struct device *dev = &client->dev;
|
|
u8 bl_data[] = { 0xa7, 0x40 };
|
|
int err;
|
|
int i;
|
|
|
|
tk = devm_kzalloc(&client->dev, sizeof(*tk), GFP_KERNEL);
|
|
if (!tk)
|
|
return -ENOMEM;
|
|
|
|
tk->input = devm_input_allocate_device(dev);
|
|
if (!tk->input)
|
|
return -ENOMEM;
|
|
|
|
tk->client = client;
|
|
tk->dev = dev;
|
|
|
|
tk->input->keycodesize = sizeof(u16);
|
|
tk->input->keycodemax = ARRAY_SIZE(tk->codes);
|
|
tk->input->keycode = tk->codes;
|
|
tk->codes[0] = KEY_UP;
|
|
tk->codes[1] = KEY_DOWN;
|
|
tk->codes[2] = KEY_LEFT;
|
|
tk->codes[3] = KEY_RIGHT;
|
|
tk->codes[4] = KEY_ENTER;
|
|
tk->codes[5] = KEY_WPS_BUTTON;
|
|
/*
|
|
* This key appears in the vendor driver, but I have
|
|
* not been able to activate it.
|
|
*/
|
|
tk->codes[6] = KEY_RESERVED;
|
|
|
|
__set_bit(EV_KEY, tk->input->evbit);
|
|
for (i = 0; i < ARRAY_SIZE(tk->codes); i++)
|
|
__set_bit(tk->codes[i], tk->input->keybit);
|
|
__clear_bit(KEY_RESERVED, tk->input->keybit);
|
|
|
|
tk->input->name = "D-Link DIR-685 touchkeys";
|
|
tk->input->id.bustype = BUS_I2C;
|
|
|
|
err = input_register_device(tk->input);
|
|
if (err)
|
|
return err;
|
|
|
|
/* Set the brightness to max level */
|
|
err = i2c_master_send(client, bl_data, sizeof(bl_data));
|
|
if (err != sizeof(bl_data))
|
|
dev_warn(tk->dev, "error setting brightness level\n");
|
|
|
|
if (!client->irq) {
|
|
dev_err(dev, "no IRQ on the I2C device\n");
|
|
return -ENODEV;
|
|
}
|
|
err = devm_request_threaded_irq(dev, client->irq,
|
|
NULL, dir685_tk_irq_thread,
|
|
IRQF_ONESHOT,
|
|
"dir685-tk", tk);
|
|
if (err) {
|
|
dev_err(dev, "can't request IRQ\n");
|
|
return err;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const struct i2c_device_id dir685_tk_id[] = {
|
|
{ "dir685tk", 0 },
|
|
{ }
|
|
};
|
|
MODULE_DEVICE_TABLE(i2c, dir685_tk_id);
|
|
|
|
#ifdef CONFIG_OF
|
|
static const struct of_device_id dir685_tk_of_match[] = {
|
|
{ .compatible = "dlink,dir685-touchkeys" },
|
|
{},
|
|
};
|
|
MODULE_DEVICE_TABLE(of, dir685_tk_of_match);
|
|
#endif
|
|
|
|
static struct i2c_driver dir685_tk_i2c_driver = {
|
|
.driver = {
|
|
.name = "dlin-dir685-touchkeys",
|
|
.of_match_table = of_match_ptr(dir685_tk_of_match),
|
|
},
|
|
.probe = dir685_tk_probe,
|
|
.id_table = dir685_tk_id,
|
|
};
|
|
module_i2c_driver(dir685_tk_i2c_driver);
|
|
|
|
MODULE_AUTHOR("Linus Walleij <linus.walleij@linaro.org>");
|
|
MODULE_DESCRIPTION("D-Link DIR-685 touchkeys driver");
|
|
MODULE_LICENSE("GPL");
|