299 lines
8.3 KiB
C
Executable File
299 lines
8.3 KiB
C
Executable File
/*
|
|
* Copyright (C) 2016 Samsung Electronics. All rights reserved.
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License
|
|
* version 2 as published by the Free Software Foundation.
|
|
*
|
|
* This program is distributed in the hope that it will be useful, but
|
|
* WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
|
|
* General Public License for more details.
|
|
*/
|
|
|
|
#ifndef _ET5XX_LINUX_DIRVER_H_
|
|
#define _ET5XX_LINUX_DIRVER_H_
|
|
|
|
#ifdef ENABLE_SENSORS_FPRINT_SECURE
|
|
#define FEATURE_SPI_WAKELOCK
|
|
#endif /* CONFIG_SEC_FACTORY */
|
|
|
|
#include <linux/module.h>
|
|
#include <linux/spi/spi.h>
|
|
|
|
#include <linux/platform_data/spi-s3c64xx.h>
|
|
#include <linux/wakelock.h>
|
|
#include <linux/regulator/consumer.h>
|
|
#ifdef ENABLE_SENSORS_FPRINT_SECURE
|
|
#include <linux/clk.h>
|
|
#include <linux/pm_runtime.h>
|
|
#include <linux/spi/spidev.h>
|
|
#include <linux/of.h>
|
|
#include <linux/of_device.h>
|
|
#include <linux/of_dma.h>
|
|
#include <linux/amba/bus.h>
|
|
#include <linux/amba/pl330.h>
|
|
#if defined(CONFIG_SECURE_OS_BOOSTER_API)
|
|
#if defined(CONFIG_SOC_EXYNOS8890) || defined(CONFIG_SOC_EXYNOS7870) \
|
|
|| defined(CONFIG_SOC_EXYNOS7880) || defined(CONFIG_SOC_EXYNOS7570) \
|
|
|| defined(CONFIG_SOC_EXYNOS7885) || defined(CONFIG_SOC_EXYNOS9810)
|
|
#include <soc/samsung/secos_booster.h>
|
|
#else
|
|
#include <mach/secos_booster.h>
|
|
#endif
|
|
#elif defined(CONFIG_TZDEV_BOOST)
|
|
#include <../drivers/misc/tzdev/tz_boost.h>
|
|
#endif
|
|
|
|
struct sec_spi_info {
|
|
int port;
|
|
unsigned long speed;
|
|
};
|
|
#endif
|
|
|
|
/*
|
|
* This feature is temporary for exynos AP only.
|
|
* It's for control GPIO config on enabled TZ before enable GPIO protection.
|
|
* If it's still defined this feature after enable GPIO protection,
|
|
* it will be happened kernel panic
|
|
* So it should be un-defined after enable GPIO protection
|
|
*/
|
|
#undef DISABLED_GPIO_PROTECTION
|
|
|
|
/*#define ET5XX_SPI_DEBUG*/
|
|
|
|
#ifdef ET5XX_SPI_DEBUG
|
|
#define DEBUG_PRINT(fmt, args...) pr_err(fmt, ## args)
|
|
#else
|
|
#define DEBUG_PRINT(fmt, args...)
|
|
#endif
|
|
|
|
#define VENDOR "EGISTEC"
|
|
#define CHIP_ID "ET5XX"
|
|
|
|
/* assigned */
|
|
#define ET5XX_MAJOR 152
|
|
/* ... up to 256 */
|
|
#define N_SPI_MINORS 32
|
|
|
|
#define OP_REG_R 0x20
|
|
#define OP_REG_R_C 0x22
|
|
#define OP_REG_R_C_BW 0x23
|
|
#define OP_REG_W 0x24
|
|
#define OP_REG_W_C 0x26
|
|
#define OP_REG_W_C_BW 0x27
|
|
#define OP_NVM_ON_R 0x40
|
|
#define OP_NVM_ON_W 0x42
|
|
#define OP_NVM_RE 0x44
|
|
#define OP_NVM_WE 0x46
|
|
#define OP_NVM_OFF 0x48
|
|
#define OP_IMG_R 0x50
|
|
#define OP_VDM_R 0x60
|
|
#define OP_VDM_W 0x62
|
|
#define BITS_PER_WORD 8
|
|
|
|
#define SLOW_BAUD_RATE 12500000
|
|
|
|
#define DRDY_IRQ_ENABLE 1
|
|
#define DRDY_IRQ_DISABLE 0
|
|
|
|
#define ET5XX_INT_DETECTION_PERIOD 10
|
|
#define ET5XX_DETECTION_THRESHOLD 10
|
|
|
|
#define FP_REGISTER_READ 0x01
|
|
#define FP_REGISTER_WRITE 0x02
|
|
#define FP_GET_ONE_IMG 0x03
|
|
#define FP_SENSOR_RESET 0x04
|
|
#define FP_POWER_CONTROL 0x05
|
|
#define FP_SET_SPI_CLOCK 0x06
|
|
#define FP_RESET_SET 0x07
|
|
#define FP_REGISTER_BREAD 0x20
|
|
#define FP_REGISTER_BWRITE 0x21
|
|
#define FP_REGISTER_MREAD 0x22
|
|
#define FP_REGISTER_MWRITE 0x23
|
|
#define FP_REGISTER_BREAD_BACKWARD 0x24
|
|
#define FP_REGISTER_BWRITE_BACKWARD 0x25
|
|
#define FP_VDM_READ 0x30
|
|
#define FP_VDM_WRITE 0x31
|
|
#define FP_NVM_READ 0X40
|
|
#define FP_NVM_WRITE 0x41
|
|
#define FP_NVM_OFF 0x42
|
|
#define FP_NVM_WRITEEX 0x43
|
|
|
|
#ifdef ENABLE_SENSORS_FPRINT_SECURE
|
|
#define FP_DISABLE_SPI_CLOCK 0x10
|
|
#define FP_CPU_SPEEDUP 0x11
|
|
#define FP_SET_SENSOR_TYPE 0x14
|
|
/* Do not use ioctl number 0x15 */
|
|
#define FP_SET_LOCKSCREEN 0x16
|
|
#define FP_SET_WAKE_UP_SIGNAL 0x17
|
|
#endif
|
|
#define FP_POWER_CONTROL_ET5XX 0x18
|
|
#define FP_SENSOR_ORIENT 0x19
|
|
#define FP_SPI_VALUE 0x1a
|
|
#define FP_IOCTL_RESERVED_01 0x1b
|
|
#define FP_IOCTL_RESERVED_02 0x1c
|
|
|
|
|
|
|
|
/* trigger signal initial routine */
|
|
#define INT_TRIGGER_INIT 0xa4
|
|
/* trigger signal close routine */
|
|
#define INT_TRIGGER_CLOSE 0xa5
|
|
/* read trigger status */
|
|
#define INT_TRIGGER_READ 0xa6
|
|
/* polling trigger status */
|
|
#define INT_TRIGGER_POLLING 0xa7
|
|
/* polling abort */
|
|
#define INT_TRIGGER_ABORT 0xa8
|
|
/* Sensor Registers */
|
|
#define FDATA_ET5XX_ADDR 0x00
|
|
#define FSTATUS_ET5XX_ADDR 0x01
|
|
/* Detect Define */
|
|
#define FRAME_READY_MASK 0x01
|
|
|
|
#define SHIFT_BYTE_OF_IMAGE 0
|
|
#define DIVISION_OF_IMAGE 4
|
|
#define LARGE_SPI_TRANSFER_BUFFER 64
|
|
#define MAX_NVM_LEN (32 * 2) /* NVM length in bytes (32 * 16 bits internally) */
|
|
#define NVM_WRITE_LENGTH 4096
|
|
#define DETECT_ADM 1
|
|
|
|
struct egis_ioc_transfer {
|
|
u8 *tx_buf;
|
|
u8 *rx_buf;
|
|
|
|
__u32 len;
|
|
__u32 speed_hz;
|
|
|
|
__u16 delay_usecs;
|
|
__u8 bits_per_word;
|
|
__u8 cs_change;
|
|
__u8 opcode;
|
|
__u8 pad[3];
|
|
};
|
|
|
|
/*
|
|
* If platform is 32bit and kernel is 64bit
|
|
* We will alloc egis_ioc_transfer for 64bit and 32bit
|
|
* We use ioc_32(32bit) to get data from user mode.
|
|
* Then copy the ioc_32 to ioc(64bit).
|
|
*/
|
|
#ifdef CONFIG_SENSORS_FINGERPRINT_32BITS_PLATFORM_ONLY
|
|
struct egis_ioc_transfer_32 {
|
|
__u32 tx_buf;
|
|
__u32 rx_buf;
|
|
__u32 len;
|
|
__u32 speed_hz;
|
|
__u16 delay_usecs;
|
|
__u8 bits_per_word;
|
|
__u8 cs_change;
|
|
__u8 opcode;
|
|
__u8 pad[3];
|
|
};
|
|
#endif
|
|
|
|
#define EGIS_IOC_MAGIC 'k'
|
|
#define EGIS_MSGSIZE(N) \
|
|
((((N)*(sizeof(struct egis_ioc_transfer))) < (1 << _IOC_SIZEBITS)) \
|
|
? ((N)*(sizeof(struct egis_ioc_transfer))) : 0)
|
|
#define EGIS_IOC_MESSAGE(N) _IOW(EGIS_IOC_MAGIC, 0, char[EGIS_MSGSIZE(N)])
|
|
|
|
struct etspi_data {
|
|
dev_t devt;
|
|
spinlock_t spi_lock;
|
|
struct spi_device *spi;
|
|
struct list_head device_entry;
|
|
|
|
/* buffer is NULL unless this device is open (users > 0) */
|
|
struct mutex buf_lock;
|
|
unsigned int users;
|
|
u8 *buf;/* tx buffer for sensor register read/write */
|
|
unsigned int bufsiz; /* MAX size of tx and rx buffer */
|
|
unsigned int drdyPin; /* DRDY GPIO pin number */
|
|
unsigned int sleepPin; /* Sleep GPIO pin number */
|
|
unsigned int ldo_pin; /* Ldo GPIO pin number */
|
|
const char *btp_vdd;
|
|
struct regulator *regulator_3p3;
|
|
#ifndef ENABLE_SENSORS_FPRINT_SECURE
|
|
#ifdef CONFIG_SOC_EXYNOS8890
|
|
/* set cs pin in fp driver, use only Exynos8890 */
|
|
/* for use auto cs mode with dualization fp sensor */
|
|
unsigned int cs_gpio;
|
|
#endif
|
|
#endif
|
|
struct pinctrl *p;
|
|
struct pinctrl_state *pins_poweron;
|
|
struct pinctrl_state *pins_poweroff;
|
|
|
|
unsigned int spi_cs; /* spi cs pin <temporary gpio setting> */
|
|
|
|
unsigned int drdy_irq_flag; /* irq flag */
|
|
bool ldo_onoff;
|
|
|
|
/* For polling interrupt */
|
|
int int_count;
|
|
struct timer_list timer;
|
|
struct work_struct work_debug;
|
|
struct workqueue_struct *wq_dbg;
|
|
struct timer_list dbg_timer;
|
|
int sensortype;
|
|
u32 spi_value;
|
|
struct device *fp_device;
|
|
#ifdef ENABLE_SENSORS_FPRINT_SECURE
|
|
bool enabled_clk;
|
|
#ifdef FEATURE_SPI_WAKELOCK
|
|
struct wake_lock fp_spi_lock;
|
|
#endif
|
|
#endif
|
|
struct wake_lock fp_signal_lock;
|
|
bool tz_mode;
|
|
int detect_period;
|
|
int detect_threshold;
|
|
bool finger_on;
|
|
const char *chipid;
|
|
bool ldo_enabled;
|
|
unsigned int orient;
|
|
int reset_count;
|
|
int interrupt_count;
|
|
};
|
|
|
|
int etspi_io_burst_read_register(struct etspi_data *etspi,
|
|
struct egis_ioc_transfer *ioc);
|
|
int etspi_io_burst_read_register_backward(struct etspi_data *etspi,
|
|
struct egis_ioc_transfer *ioc);
|
|
int etspi_io_burst_write_register(struct etspi_data *etspi,
|
|
struct egis_ioc_transfer *ioc);
|
|
int etspi_io_burst_write_register_backward(struct etspi_data *etspi,
|
|
struct egis_ioc_transfer *ioc);
|
|
int etspi_io_read_register(struct etspi_data *etspi,
|
|
u8 *addr, u8 *buf);
|
|
int etspi_io_read_registerex(struct etspi_data *etspi,
|
|
u8 *addr, u8 *buf, u32 len);
|
|
int etspi_io_write_register(struct etspi_data *etspi,
|
|
u8 *buf);
|
|
int etspi_read_register(struct etspi_data *etspi,
|
|
u8 addr, u8 *buf);
|
|
int etspi_write_register(struct etspi_data *etspi,
|
|
u8 addr, u8 buf);
|
|
int etspi_io_nvm_read(struct etspi_data *etspi,
|
|
struct egis_ioc_transfer *ioc);
|
|
int etspi_io_nvm_write(struct etspi_data *etspi,
|
|
struct egis_ioc_transfer *ioc);
|
|
int etspi_io_nvm_writeex(struct etspi_data *etspi,
|
|
struct egis_ioc_transfer *ioc);
|
|
int etspi_io_nvm_off(struct etspi_data *etspi,
|
|
struct egis_ioc_transfer *ioc);
|
|
int etspi_io_vdm_read(struct etspi_data *etspi,
|
|
struct egis_ioc_transfer *ioc);
|
|
int etspi_io_vdm_write(struct etspi_data *etspi,
|
|
struct egis_ioc_transfer *ioc);
|
|
int etspi_io_get_frame(struct etspi_data *etspi, u8 *frame, u32 size);
|
|
|
|
extern int fingerprint_register(struct device *dev, void *drvdata,
|
|
struct device_attribute *attributes[], char *name);
|
|
extern void fingerprint_unregister(struct device *dev,
|
|
struct device_attribute *attributes[]);
|
|
|
|
#endif
|