162 lines
6.7 KiB
Plaintext
Executable File
162 lines
6.7 KiB
Plaintext
Executable File
Kernel driver w83791d
|
|
=====================
|
|
|
|
Supported chips:
|
|
* Winbond W83791D
|
|
Prefix: 'w83791d'
|
|
Addresses scanned: I2C 0x2c - 0x2f
|
|
Datasheet: http://www.winbond-usa.com/products/winbond_products/pdfs/PCIC/W83791D_W83791Gb.pdf
|
|
|
|
Author: Charles Spirakis <bezaur@gmail.com>
|
|
|
|
This driver was derived from the w83781d.c and w83792d.c source files.
|
|
|
|
Credits:
|
|
w83781d.c:
|
|
Frodo Looijaard <frodol@dds.nl>,
|
|
Philip Edelbrock <phil@netroedge.com>,
|
|
and Mark Studebaker <mdsxyz123@yahoo.com>
|
|
w83792d.c:
|
|
Shane Huang (Winbond),
|
|
Rudolf Marek <r.marek@assembler.cz>
|
|
|
|
Additional contributors:
|
|
Sven Anders <anders@anduras.de>
|
|
Marc Hulsman <m.hulsman@tudelft.nl>
|
|
|
|
Module Parameters
|
|
-----------------
|
|
|
|
* init boolean
|
|
(default 0)
|
|
Use 'init=1' to have the driver do extra software initializations.
|
|
The default behavior is to do the minimum initialization possible
|
|
and depend on the BIOS to properly setup the chip. If you know you
|
|
have a w83791d and you're having problems, try init=1 before trying
|
|
reset=1.
|
|
|
|
* reset boolean
|
|
(default 0)
|
|
Use 'reset=1' to reset the chip (via index 0x40, bit 7). The default
|
|
behavior is no chip reset to preserve BIOS settings.
|
|
|
|
* force_subclients=bus,caddr,saddr,saddr
|
|
This is used to force the i2c addresses for subclients of
|
|
a certain chip. Example usage is `force_subclients=0,0x2f,0x4a,0x4b'
|
|
to force the subclients of chip 0x2f on bus 0 to i2c addresses
|
|
0x4a and 0x4b.
|
|
|
|
|
|
Description
|
|
-----------
|
|
|
|
This driver implements support for the Winbond W83791D chip. The W83791G
|
|
chip appears to be the same as the W83791D but is lead free.
|
|
|
|
Detection of the chip can sometimes be foiled because it can be in an
|
|
internal state that allows no clean access (Bank with ID register is not
|
|
currently selected). If you know the address of the chip, use a 'force'
|
|
parameter; this will put it into a more well-behaved state first.
|
|
|
|
The driver implements three temperature sensors, ten voltage sensors,
|
|
five fan rotation speed sensors and manual PWM control of each fan.
|
|
|
|
Temperatures are measured in degrees Celsius and measurement resolution is 1
|
|
degC for temp1 and 0.5 degC for temp2 and temp3. An alarm is triggered when
|
|
the temperature gets higher than the Overtemperature Shutdown value; it stays
|
|
on until the temperature falls below the Hysteresis value.
|
|
|
|
Voltage sensors (also known as IN sensors) report their values in millivolts.
|
|
An alarm is triggered if the voltage has crossed a programmable minimum
|
|
or maximum limit.
|
|
|
|
Fan rotation speeds are reported in RPM (rotations per minute). An alarm is
|
|
triggered if the rotation speed has dropped below a programmable limit. Fan
|
|
readings can be divided by a programmable divider (1, 2, 4, 8, 16,
|
|
32, 64 or 128 for all fans) to give the readings more range or accuracy.
|
|
|
|
Each fan controlled is controlled by PWM. The PWM duty cycle can be read and
|
|
set for each fan separately. Valid values range from 0 (stop) to 255 (full).
|
|
PWM 1-3 support Thermal Cruise mode, in which the PWMs are automatically
|
|
regulated to keep respectively temp 1-3 at a certain target temperature.
|
|
See below for the description of the sysfs-interface.
|
|
|
|
The w83791d has a global bit used to enable beeping from the speaker when an
|
|
alarm is triggered as well as a bitmask to enable or disable the beep for
|
|
specific alarms. You need both the global beep enable bit and the
|
|
corresponding beep bit to be on for a triggered alarm to sound a beep.
|
|
|
|
The sysfs interface to the global enable is via the sysfs beep_enable file.
|
|
This file is used for both legacy and new code.
|
|
|
|
The sysfs interface to the beep bitmask has migrated from the original legacy
|
|
method of a single sysfs beep_mask file to a newer method using multiple
|
|
*_beep files as described in .../Documentation/hwmon/sysfs-interface.
|
|
|
|
A similar change has occurred for the bitmap corresponding to the alarms. The
|
|
original legacy method used a single sysfs alarms file containing a bitmap
|
|
of triggered alarms. The newer method uses multiple sysfs *_alarm files
|
|
(again following the pattern described in sysfs-interface).
|
|
|
|
Since both methods read and write the underlying hardware, they can be used
|
|
interchangeably and changes in one will automatically be reflected by
|
|
the other. If you use the legacy bitmask method, your user-space code is
|
|
responsible for handling the fact that the alarms and beep_mask bitmaps
|
|
are not the same (see the table below).
|
|
|
|
NOTE: All new code should be written to use the newer sysfs-interface
|
|
specification as that avoids bitmap problems and is the preferred interface
|
|
going forward.
|
|
|
|
The driver reads the hardware chip values at most once every three seconds.
|
|
User mode code requesting values more often will receive cached values.
|
|
|
|
/sys files
|
|
----------
|
|
The sysfs-interface is documented in the 'sysfs-interface' file. Only
|
|
chip-specific options are documented here.
|
|
|
|
pwm[1-3]_enable - this file controls mode of fan/temperature control for
|
|
fan 1-3. Fan/PWM 4-5 only support manual mode.
|
|
* 1 Manual mode
|
|
* 2 Thermal Cruise mode
|
|
* 3 Fan Speed Cruise mode (no further support)
|
|
|
|
temp[1-3]_target - defines the target temperature for Thermal Cruise mode.
|
|
Unit: millidegree Celsius
|
|
RW
|
|
|
|
temp[1-3]_tolerance - temperature tolerance for Thermal Cruise mode.
|
|
Specifies an interval around the target temperature
|
|
in which the fan speed is not changed.
|
|
Unit: millidegree Celsius
|
|
RW
|
|
|
|
Alarms bitmap vs. beep_mask bitmask
|
|
------------------------------------
|
|
For legacy code using the alarms and beep_mask files:
|
|
|
|
in0 (VCORE) : alarms: 0x000001 beep_mask: 0x000001
|
|
in1 (VINR0) : alarms: 0x000002 beep_mask: 0x002000 <== mismatch
|
|
in2 (+3.3VIN): alarms: 0x000004 beep_mask: 0x000004
|
|
in3 (5VDD) : alarms: 0x000008 beep_mask: 0x000008
|
|
in4 (+12VIN) : alarms: 0x000100 beep_mask: 0x000100
|
|
in5 (-12VIN) : alarms: 0x000200 beep_mask: 0x000200
|
|
in6 (-5VIN) : alarms: 0x000400 beep_mask: 0x000400
|
|
in7 (VSB) : alarms: 0x080000 beep_mask: 0x010000 <== mismatch
|
|
in8 (VBAT) : alarms: 0x100000 beep_mask: 0x020000 <== mismatch
|
|
in9 (VINR1) : alarms: 0x004000 beep_mask: 0x004000
|
|
temp1 : alarms: 0x000010 beep_mask: 0x000010
|
|
temp2 : alarms: 0x000020 beep_mask: 0x000020
|
|
temp3 : alarms: 0x002000 beep_mask: 0x000002 <== mismatch
|
|
fan1 : alarms: 0x000040 beep_mask: 0x000040
|
|
fan2 : alarms: 0x000080 beep_mask: 0x000080
|
|
fan3 : alarms: 0x000800 beep_mask: 0x000800
|
|
fan4 : alarms: 0x200000 beep_mask: 0x200000
|
|
fan5 : alarms: 0x400000 beep_mask: 0x400000
|
|
tart1 : alarms: 0x010000 beep_mask: 0x040000 <== mismatch
|
|
tart2 : alarms: 0x020000 beep_mask: 0x080000 <== mismatch
|
|
tart3 : alarms: 0x040000 beep_mask: 0x100000 <== mismatch
|
|
case_open : alarms: 0x001000 beep_mask: 0x001000
|
|
global_enable: alarms: -------- beep_mask: 0x800000 (modified via beep_enable)
|