85 lines
4.0 KiB
Plaintext
85 lines
4.0 KiB
Plaintext
|
QCOM Idle States for cpuidle driver
|
||
|
|
|
||
|
|
ARM provides idle-state node to define the cpuidle states, as defined in [1].
|
||
|
|
cpuidle-qcom is the cpuidle driver for Qualcomm SoCs and uses these idle
|
||
|
|
states. Idle states have different enter/exit latency and residency values.
|
||
|
|
The idle states supported by the QCOM SoC are defined as -
|
||
|
|
|
||
|
|
* Standby
|
||
|
|
* Retention
|
||
|
|
* Standalone Power Collapse (Standalone PC or SPC)
|
||
|
|
* Power Collapse (PC)
|
||
|
|
|
||
|
|
Standby: Standby does a little more in addition to architectural clock gating.
|
||
|
|
When the WFI instruction is executed the ARM core would gate its internal
|
||
|
|
clocks. In addition to gating the clocks, QCOM cpus use this instruction as a
|
||
|
|
trigger to execute the SPM state machine. The SPM state machine waits for the
|
||
|
|
interrupt to trigger the core back in to active. This triggers the cache
|
||
|
|
hierarchy to enter standby states, when all cpus are idle. An interrupt brings
|
||
|
|
the SPM state machine out of its wait, the next step is to ensure that the
|
||
|
|
cache hierarchy is also out of standby, and then the cpu is allowed to resume
|
||
|
|
execution. This state is defined as a generic ARM WFI state by the ARM cpuidle
|
||
|
|
driver and is not defined in the DT. The SPM state machine should be
|
||
|
|
configured to execute this state by default and after executing every other
|
||
|
|
state below.
|
||
|
|
|
||
|
|
Retention: Retention is a low power state where the core is clock gated and
|
||
|
|
the memory and the registers associated with the core are retained. The
|
||
|
|
voltage may be reduced to the minimum value needed to keep the processor
|
||
|
|
registers active. The SPM should be configured to execute the retention
|
||
|
|
sequence and would wait for interrupt, before restoring the cpu to execution
|
||
|
|
state. Retention may have a slightly higher latency than Standby.
|
||
|
|
|
||
|
|
Standalone PC: A cpu can power down and warmboot if there is a sufficient time
|
||
|
|
between the time it enters idle and the next known wake up. SPC mode is used
|
||
|
|
to indicate a core entering a power down state without consulting any other
|
||
|
|
cpu or the system resources. This helps save power only on that core. The SPM
|
||
|
|
sequence for this idle state is programmed to power down the supply to the
|
||
|
|
core, wait for the interrupt, restore power to the core, and ensure the
|
||
|
|
system state including cache hierarchy is ready before allowing core to
|
||
|
|
resume. Applying power and resetting the core causes the core to warmboot
|
||
|
|
back into Elevation Level (EL) which trampolines the control back to the
|
||
|
|
kernel. Entering a power down state for the cpu, needs to be done by trapping
|
||
|
|
into a EL. Failing to do so, would result in a crash enforced by the warm boot
|
||
|
|
code in the EL for the SoC. On SoCs with write-back L1 cache, the cache has to
|
||
|
|
be flushed in s/w, before powering down the core.
|
||
|
|
|
||
|
|
Power Collapse: This state is similar to the SPC mode, but distinguishes
|
||
|
|
itself in that the cpu acknowledges and permits the SoC to enter deeper sleep
|
||
|
|
modes. In a hierarchical power domain SoC, this means L2 and other caches can
|
||
|
|
be flushed, system bus, clocks - lowered, and SoC main XO clock gated and
|
||
|
|
voltages reduced, provided all cpus enter this state. Since the span of low
|
||
|
|
power modes possible at this state is vast, the exit latency and the residency
|
||
|
|
of this low power mode would be considered high even though at a cpu level,
|
||
|
|
this essentially is cpu power down. The SPM in this state also may handshake
|
||
|
|
with the Resource power manager (RPM) processor in the SoC to indicate a
|
||
|
|
complete application processor subsystem shut down.
|
||
|
|
|
||
|
|
The idle-state for QCOM SoCs are distinguished by the compatible property of
|
||
|
|
the idle-states device node.
|
||
|
|
|
||
|
|
The devicetree representation of the idle state should be -
|
||
|
|
|
||
|
|
Required properties:
|
||
|
|
|
||
|
|
- compatible: Must be one of -
|
||
|
|
"qcom,idle-state-ret",
|
||
|
|
"qcom,idle-state-spc",
|
||
|
|
"qcom,idle-state-pc",
|
||
|
|
and "arm,idle-state".
|
||
|
|
|
||
|
|
Other required and optional properties are specified in [1].
|
||
|
|
|
||
|
|
Example:
|
||
|
|
|
||
|
|
idle-states {
|
||
|
|
CPU_SPC: spc {
|
||
|
|
compatible = "qcom,idle-state-spc", "arm,idle-state";
|
||
|
|
entry-latency-us = <150>;
|
||
|
|
exit-latency-us = <200>;
|
||
|
|
min-residency-us = <2000>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
[1]. Documentation/devicetree/bindings/arm/idle-states.txt
|