125 lines
2.8 KiB
Plaintext
125 lines
2.8 KiB
Plaintext
|
* Analog Device AD5755 IIO Multi-Channel DAC Linux Driver
|
||
|
|
|
||
|
|
Required properties:
|
||
|
|
- compatible: Has to contain one of the following:
|
||
|
|
adi,ad5755
|
||
|
|
adi,ad5755-1
|
||
|
|
adi,ad5757
|
||
|
|
adi,ad5735
|
||
|
|
adi,ad5737
|
||
|
|
|
||
|
|
- reg: spi chip select number for the device
|
||
|
|
- spi-cpha or spi-cpol: is the only modes that is supported
|
||
|
|
|
||
|
|
Recommended properties:
|
||
|
|
- spi-max-frequency: Definition as per
|
||
|
|
Documentation/devicetree/bindings/spi/spi-bus.txt
|
||
|
|
|
||
|
|
Optional properties:
|
||
|
|
See include/dt-bindings/iio/ad5755.h
|
||
|
|
- adi,ext-dc-dc-compenstation-resistor: boolean set if the hardware have an
|
||
|
|
external resistor and thereby bypasses
|
||
|
|
the internal compensation resistor.
|
||
|
|
- adi,dc-dc-phase:
|
||
|
|
Valid values for DC DC Phase control is:
|
||
|
|
0: All dc-to-dc converters clock on the same edge.
|
||
|
|
1: Channel A and Channel B clock on the same edge,
|
||
|
|
Channel C and Channel D clock on opposite edges.
|
||
|
|
2: Channel A and Channel C clock on the same edge,
|
||
|
|
Channel B and Channel D clock on opposite edges.
|
||
|
|
3: Channel A, Channel B, Channel C, and Channel D
|
||
|
|
clock 90 degrees out of phase from each other.
|
||
|
|
- adi,dc-dc-freq-hz:
|
||
|
|
Valid values for DC DC frequency is [Hz]:
|
||
|
|
250000
|
||
|
|
410000
|
||
|
|
650000
|
||
|
|
- adi,dc-dc-max-microvolt:
|
||
|
|
Valid values for the maximum allowed Vboost voltage supplied by
|
||
|
|
the dc-to-dc converter is:
|
||
|
|
23000000
|
||
|
|
24500000
|
||
|
|
27000000
|
||
|
|
29500000
|
||
|
|
|
||
|
|
Optional for every channel:
|
||
|
|
- adi,mode:
|
||
|
|
Valid values for DAC modes is:
|
||
|
|
0: 0 V to 5 V voltage range.
|
||
|
|
1: 0 V to 10 V voltage range.
|
||
|
|
2: Plus minus 5 V voltage range.
|
||
|
|
3: Plus minus 10 V voltage range.
|
||
|
|
4: 4 mA to 20 mA current range.
|
||
|
|
5: 0 mA to 20 mA current range.
|
||
|
|
6: 0 mA to 24 mA current range.
|
||
|
|
- adi,ext-current-sense-resistor: boolean set if the hardware a external
|
||
|
|
current sense resistor.
|
||
|
|
- adi,enable-voltage-overrange: boolean enable voltage overrange
|
||
|
|
- adi,slew: Array of slewrate settings should contain 3 fields:
|
||
|
|
1: Should be either 0 or 1 in order to enable or disable slewrate.
|
||
|
|
2: Slew rate settings:
|
||
|
|
Valid values for the slew rate update frequency:
|
||
|
|
64000
|
||
|
|
32000
|
||
|
|
16000
|
||
|
|
8000
|
||
|
|
4000
|
||
|
|
2000
|
||
|
|
1000
|
||
|
|
500
|
||
|
|
250
|
||
|
|
125
|
||
|
|
64
|
||
|
|
32
|
||
|
|
16
|
||
|
|
8
|
||
|
|
4
|
||
|
|
0
|
||
|
|
3: Slew step size:
|
||
|
|
Valid values for the step size LSBs:
|
||
|
|
1
|
||
|
|
2
|
||
|
|
4
|
||
|
|
16
|
||
|
|
32
|
||
|
|
64
|
||
|
|
128
|
||
|
|
256
|
||
|
|
|
||
|
|
Example:
|
||
|
|
dac@0 {
|
||
|
|
#address-cells = <1>;
|
||
|
|
#size-cells = <0>;
|
||
|
|
compatible = "adi,ad5755";
|
||
|
|
reg = <0>;
|
||
|
|
spi-max-frequency = <1000000>;
|
||
|
|
spi-cpha;
|
||
|
|
adi,dc-dc-phase = <0>;
|
||
|
|
adi,dc-dc-freq-hz = <410000>;
|
||
|
|
adi,dc-dc-max-microvolt = <23000000>;
|
||
|
|
channel@0 {
|
||
|
|
reg = <0>;
|
||
|
|
adi,mode = <4>;
|
||
|
|
adi,ext-current-sense-resistor;
|
||
|
|
adi,slew = <0 64000 1>;
|
||
|
|
};
|
||
|
|
channel@1 {
|
||
|
|
reg = <1>;
|
||
|
|
adi,mode = <4>;
|
||
|
|
adi,ext-current-sense-resistor;
|
||
|
|
adi,slew = <0 64000 1>;
|
||
|
|
};
|
||
|
|
channel@2 {
|
||
|
|
reg = <2>;
|
||
|
|
adi,mode = <4>;
|
||
|
|
adi,ext-current-sense-resistor;
|
||
|
|
adi,slew = <0 64000 1>;
|
||
|
|
};
|
||
|
|
channel@3 {
|
||
|
|
reg = <3>;
|
||
|
|
adi,mode = <4>;
|
||
|
|
adi,ext-current-sense-resistor;
|
||
|
|
adi,slew = <0 64000 1>;
|
||
|
|
};
|
||
|
|
};
|